Free Ammonia Deliming: Effect of Tartaric Acid Addition as a Deliming Agent on The Quality of Wet Blue and Wastewater

  • A. W. Nugraha Department of Agro-Industrial Engineering, Faculty of Agricultural Technology, IPB University
  • O. Suparno Department of Agro-Industrial Engineering, Faculty of Agricultural Technology, IPB University
  • N. S. Indrasti Department of Agro-Industrial Engineering, Faculty of Agricultural Technology, IPB University
  • Hoerudin Hoerudin Indonesian Center for Agricultural Post Harvest Research and Development
Keywords: tartaric acid, deliming agent, wet blue, wastewater

Abstract

The objective of this study was to evaluate the pelt and wastewater characteristics after deliming process in an acid condition by tartaric acid, also wet blue properties that were formed. Various observed variables were the dose of tartaric acid, pelt thickness, calcium content, physical and chemical properties of wet blue, such as tensile strength, tear strength, elongation, shrinkage temperature, and chrome oxide content, as well as the pollutants content of wastewater as chemical oxygen demand (COD), biological oxygen demand (BOD), total suspended solid (TSS), and total dissolve solid (TDS). The experiment used a completely randomized design with a factorial arrangement. The first factor was pH variables consisted of 3 levels, i.e., 4, 5, and 6 in the final deliming solution. The second factor was the deliming time consisted of 3 levels, i.e., 45 min, 60 min, and 75 min. Data were analyzed using Analysis of Variance (ANOVA) and then Duncan’s Multiple Range Test (DMRT). The results showed that deliming for 60 min and the pH of 5 at the end of the solution was the best treatment to remove calcium content in the pelt and reduce the thickness of pelt. It did not affect the physical and chemical quality, such as tensile strength, tear strength, elongation at break, and shrinkage temperature of the wet blue produced. Also, the quality of wastewater produced was better than the use of ammonium sulfate as a deliming agent. It can be concluded that the use of tartaric acid as pH regulator of deliming stage at pH 5 for 60 min can be used as an alternative deliming agent to substitute ammonium sulfate.

Downloads

Download data is not yet available.

References

Aleixandre, M. V. G., J. A. M. Roca, & A. B. Pia. 2011. Reducing sulfates concentration in the tannery effluent by applying pollution prevention technique and nanofiltration. J. Clean. Prod. 19: 91-98. https://doi.org/10.1016/j.jclepro.2010.09.006

APHA. 2017. Standard methods for the examination of water and wastewater. 23th ed. APHA, AWWA, WPCF, Washington.

ASTM. 2001. Annual Book of ASTM Standards. Vol 15.04. West Conshohocken, USA. ASTM.

Beghetto, V., A. Zancanaro, A. Scrivanti, U. Matteoli, & G. Pozza. 2013. The leather industry: A chemistry insight part I: an overview of the industrial process. Sci. At Ca’ Foscari. 2013:13-22

BSN. 1998. SNI 4593: 1998 Kulit jaket domba/kambing. BSN, Jakarta.

Cheng, H. M., M. Chen, & Z. Q. Li. 2014. The role of neutral salt for the hydrolysis and hierarchical structure of hide fiber in pickling. J. Am. Leather Chem. Assoc. 109: 125-130.

Chowdhury, M. J., Md. T. Uddin., Md. A. Razzaq, Al-Mizan, & A. H. Quadery. 2018. Ammonia - Reduced deliming using glycolic acid and EDTA and its effect on tannery effluent and quality of leather. J. Am. Leather Chem. Assoc. 113: 212 - 216.

Colak, S. M. & E. Kilic. 2007. The application of different deliming agents for decreasing ammonium pollution load caused by deliming operation in leather industry and the effects of these deliming agents on leather quality and effluent pollution load. J. Sci. Technol. 1: 252-263.

Covington, A. D. & W. R. Wise. 2019. Tanning Chemistry: the science of leather: edition 2. RSC Publising, UK.

Dai, G., J. Shang, & B. Qiu. 2012. Ammonia may play an important role in the cyanobacterial blooms and the distribution algal species in shallow freshwater lakes. Glob. Chang. Biol. 18: 1571-1581. https://doi.org/10.1111/j.1365-2486.2012.02638.x

Dellman, H. D. & E. N. Brown. 1992. Histologi Veteriner. Translated by R. Hartono. Universitas Indonesia Press, Jakarta.

Guthrie, S., S. Giles, F. Dunkerley, H. Tabaqchali, A. Harshfield, B. Ioppolo, & C. Manville. 2018. The Impact of Ammonia Emissions from Agriculture on Biodiversity. The Royal Society. The RAND Corporation, Santa Monica, Calif., and Cambridge, UK United Kingdom. https://doi.org/10.7249/RR2695

Gallego-Molina, A., J. A. Mendoza-Roca, D. Aguado, & M. V. Galiana-Aleixandre. 2013. Reducing pollution from the deliming-bating operation in a tannery. Wastewater reuse by microfiltration membranes. Chem. Eng. Res. Des. 91: 369-376. https://doi.org/10.1016/j.cherd.2012.08.003

Ghimire, U., M. Jang, S. P. Jung, D. Park, S. J. Park, H. Yu, & S. E. Oh. 2019. Electrochemical removal of ammonium nitrogen and COD of domestic wastewater using platinum coated titanium as an anode electrode. Energ. 12: 883. https://doi.org/10.3390/en12050883

Hashem, M. A., A. Islam, S. Paul, & S. Nasrin. 2014. Generation of ammonia in deliming operation from tannery and its environmental effect: Bangladesh perspective. Int. J. Renew. Energ. Environ. Eng. 2: 266-270.

Hu, J., & W. Deng. 2015. Application of Supercritical Carbon Dioxide for Leather Processing, J. Clean. Prod. 113: 931-946. https://doi.org/10.1016/j.jclepro.2015.10.104

Kanagy, R. J. 1977. Physical and Performance Properties of Leather. Robert E. Krieger Publishing So. Hunting, New York.

Keerthi, V. S., M. Mahalakshmi, & N. Balasubramanian. 2013. Development of hybrid membrane bioreactor for tannery effluent treatment. Desalin. 309: 231-236. https://doi.org/10.1016/j.desal.2012.10.014

Le, T. T. H., J. Fettig, & G. Meon. 2019. Kinetics and simulation of nitrification at various pH values of a polluted river in the tropics. Ecohydrol. Hydrobiol. 19: 54-65. https://doi.org/10.1016/j.ecohyd.2018.06.006

Lei, C., Y. Lin, Y. Zeng, Y. Wang, Y. Yuan, & B. Shi. 2019. A cleaner deliming technology with glycine for ammonia - nitrogen reduction in leather manufacture. J. Clean. Prod. 245. https://doi.org/10.1016/j.jclepro.2019.118900

Liu, C. K., N. P. Latona, M. M. Taylor, & R. J. Latona. 2013. Effects of bating, pickling and crosslinking treatments on the characteristics of fibrous networks from un-tanned hides. J. Am. Leather Chem. Assoc. 108: 79-85.

Mandal, T., D. Dasgupta, S. Mandal, & S. Datta. 2010. Treatment of leather industry wastewater by aerobic biological and fenton oxidation process. J. Hazard. Mater. 180: 204-211. https://doi.org/10.1016/j.jhazmat.2010.04.014

Mann, B. R., & M. M. McMillan. 2017. The Chemistry of Leather Industry. https://nzic.org.nz/app/uploads/2017/10/5C.pdf [24 September 2019].

Murti, R. S., C. M. H. Purwanti, & Suyatini. 2013. Adsorption of ammonia from tannery wastewater using bagasse fly ash. Maj. Kulit, Karet dan Plastik. 29: 85-90. In Indonesian. https://doi.org/10.20543/mkkp.v29i2.195

Nugraha, A. W., O. Suparno, & N. S. Indrasti. 2018. Material, energy and toxicity analyses (MET) in leather industry for identification of cleaner production strategies. J. Teknol. Ind. Pertan. 28: 48-60. In Indonesian. https://doi.org/10.24961/j.tek.ind.pert.2018.28.1.48

O’Flaherty, F., W. T. Roody, & R.M. Lollar. 1978. The chemistry and technology of leather. Reinhold Publishing Corporation, New York.

Qiang, X., X. Tang, & H. Zhang. 2012. Study on clean leather deliming process with sulfonated phthalic magnesium salt. Adv. Mater. Res. 393-395: 308-311. https://doi.org/10.4028/www.scientific.net/AMR.393-395.308

Rabizadeh, T., C. L. Peacock, & L. G. Benning. 2014. Carboxylic acids: effective inhibitors for calcium sulfate precipitation?. Mineral. Mag. 78: 1465-1472. https://doi.org/10.1180/minmag.2014.078.6.13

Sathish, M., B. Madhan, P. Saravan, J. R. Rao, & B. U. Nair. 2013. Dry ice - an eco - friendly alternative for ammonium reduction in leather manufacturing. J. Clean. Prod. 54: 289 - 295. https://doi.org/10.1016/j.jclepro.2013.04.046

Sharphouse, J. H. 1991. Leather Technicians’s Handbook. Leather Product Association 9th. Thomas Street, London.

Sivakumar, V., C. Ponnusawmy, K. Sudalaimani, T. Rangasamy, C. Muralidharan, & A. B. Mandal. 2015. Ammonia free deliming process in leather industry based on eco-benign products. J. Sci. Ind. Res. 74: 518- 521.

Sirvaityte, J., V. Valeika, K. Beleska, & V. Valekiene. 2007. Action of paracetic acid on calcium in limed pelt. J. Soc. Leather Technol. Chem. 91:123.

SLTC. 1996. Official Methods of Analysis. SLTC, Northampton (UK).

Stoller, M., D. Sannino, & A. Chianese. 2013. Successful filtration of membrane technologies in a conventional purification process of tannery wastewater streams. Membr. 3: 126-135. https://doi.org/10.3390/membranes3030126

Sui, Z., L. Zhang, & J. Song. 2012. Properties of environment friendly nitrogen - free materials for leather deliming. Adv. Mater. Res. 532-533: 126-130. https://doi.org/10.4028/www.scientific.net/AMR.532-533.126

Suparno, O. & E. Wahyudi. 2012. The effects of sodium percarbonate concentration and amount of water in the chamois tanning on the chamois leather quality. J. Teknol. Ind. Pertan. 22: 1-9. In Indonesian.

Uddin, T., M. J. Chowdhury, A. Razzaq, Al Mizan, & A. H. Quadery. 2018. Ammonia-free deliming using glycolic acid and EDTA and its effect on tannery effluent and quality of leather. J. Ind. Pollut. Control. 34: 1957-1960.

USDA. 2011. Tartaric Acid Handling. Technical Evaluation Report. 1-12. https://www.ams.usda.gov›default›files›media [14 October 2019]

Wang, J. & Y. Liu. 2011. Study on the treatment of tannery wastewater with the high concentration of ammonia nitrogen by MBR. Appl. Mech. Mater. 71-78: 2186-2189. https://doi.org/10.4028/www.scientific.net/AMM.71-78.2186

Wang, Y., Y. Zeng, X. Chai, X. Liao, Q. He, & B. Shi. 2012. Ammonia nitrogen in tannery wastewater: distribution, origin, and prevention. J. Am. Leather Chem. Assoc. 107: 40-50.

Wang, Y., Y. Zeng, X. Liao, W. Zhang, & B. Shi. 2013. Removal of calcium from pelt during bating process: an effective approach for non-ammonia bating. J. Am. Leather Chem. Assoc. 108: 120-127.

Wuana, R. A., F. E. Okieimen, & J. A. Imborvungu. 2010. Removal of heavy metals from a contaminated soil using organic chelating acids. Int. J. Environ. Sci. Technol. 7: 485-496. https://doi.org/10.1007/BF03326158

Yunnen, C., X. Changshi, & N. Jinxia. 2016. Removal of ammonia nitrogen from wastewater using modified activated sludge. Pol. J. Environ. Stud. 25: 415-425. https://doi.org/10.15244/pjoes/60859

Zeng, Y., J. Lu, X. Liao, Q. He, & B. Shi. 2011. Non-ammonia deliming using sodium hexametaphospate and boric acid. J. Am. Leather Chem. Assoc. 106: 257-263.

Zeng, Y., Y. Wang, Y. Song, J. Zhou, & B. Shi. 2018. A cleaner deliming process using sodium gluconate for reduction in nitrogen pollution in leather manufacture. J. Am. Leather Chem. Assoc. 113: 19-25.

Published
2020-06-06
How to Cite
Nugraha, A. W., Suparno, O., Indrasti, N. S., & Hoerudin, H. (2020). Free Ammonia Deliming: Effect of Tartaric Acid Addition as a Deliming Agent on The Quality of Wet Blue and Wastewater. Tropical Animal Science Journal, 43(2), 176-182. https://doi.org/10.5398/tasj.2020.43.2.176