Faktor Stabilitas Balok Kayu pada Konfigurasi Pembebanan Terpusat
Stability Factor of Wooden Beams in One Point Loading
Abstract
The use of wood as a building material must be designed quite rigid and strong. According to SNI 7973:2013, the corrected design value on the wooden structure components must be in accordance with the condition of wood to be used. The objective of this study is to determine the value of timber beams stability (CL) both of softwood and hardwood based on SNI 7973:2013 for construction purposes. The material in this research to be used are pine (Pinus merkusii), agathis (Agathis dammara), mahagony (Swietenia macrophylla), and red meranti (Shorea leprosula). Testing of physical properties include moisture content, specific gravity, and density, meanwhile testing of mechanical properties include flexural strength, modulus of elasticity, and ductility. Mechanical testing is carried out on a small clear specimens and full-size specimens, while the physical properties are tested only on a small clear specimens. The full-size specimens are visually sorted and the strength ratio (S) is determined prior to mechanical testing. The result of this study showed that the highest strength ratio was in meranti 55.85%, agathis 52.98%, pine 46.76%, and mahogany 46.60%. Softwood has a lower S value to more knot defects than hardwood. The slenderness ratios of agathis, pine, mahogany, and meranti wood respectively are 7.48, 7.45, 7.40 and 7.66 so that all specimens are referred to as short beams. The value of beam stability (CL) is close to 1 that indicates that the beams are stable and does not twist.
Downloads
References
Adebara SA, Haruna H, Shittu MB, Anifowose MA. Quality and utilization of timber species for building construction in Minna, Nigeria. The Internat J Engine And Sci. 2014; 3(5): 46-50.
Joseph P, Tretsiakova-McNally S. Sustainable non-metallic building materials. Sustainability. 2010; 2(2): 400–427. doi: 10.3390/su2020400.
Silva DAL, Lahr FAR, Faria OB, Chahud E. Influence of wood moisture content on the Modulus of Elasticity in compression Parallel to the grain. Material Research. 2021; 15(2): 300-304. doi: 10.1590/S1516-14392012005000025.
Wieruszewski M, Mazela B. Cross laminated timber (CLT) as an alternative form of construction wood. Drvna Industrija. 2017; 68(4): 359-367. doi: 10.5552/drind.2017.1728.
Ramage MH et al. The wood from the trees: The use of timber in construction. J Renew and sustain energy. 2017; 68: 333-359. doi: 10.1016/j.rser.2016.09.107.
Kuzman MK, Groselj P. Wood as a construction material: comparison of different construction types for residential building using the analytic hierarchy process. Wood Res. 2012; 57(4): 591–600.
Høibø O, Hansen E, Nybakk E. Building material preferences with a focus on wood in urban housing: durability and environmental impacts. Canadian J Forest Res. 2015; 45(11): 1617–1627. doi: 10.1139/cjfr-2015-0123.
Lapeantu SK, Hapid A, Muthmainnah. 2017. Sifat mekanika kayu pinus (Pinus merkusii Jungh et de Vriese) asal desa Taende Mori Atas Morowali Utara Sulawesi Tengah. Warta Rimba. 5(1): 121-126.
Simpson WT. 1999. Wood Handbook—Wood as An Engineering Material. Gen. Tech. Rep. FPL–GTR–113. Madison (US): Forest Products Laboratory.
Fernandes A, Saridan A. 2013. Sifat fisik dan mekanik kayu Shorea macroptera ssp. Sandakanensis (Sym.) Ashton sebagai bahan baku mebel. J Penelit Dipterokarpa.7(1): 1-6. doi: 10.20886/jped.2013.7.1.1-6.
Asroni A. 2008. Kolom Pondasi dan Balok T Beton Bertulang. Surakarta (ID): Universitas Muhammadiyah.
[BSN] Badan Standardisasi Nasional. 2013. SNI 7973:2013 Spesifikasi Desain untuk Kontruksi Kayu. Jakarta (ID): BSN.
[AWC] American Wood Council. 2011. ANSI/NDS 2012: National Design Specification for Wood Construction 2012. Leesburg(USA): The American Wood Council.
Richard MJ. 2013. Assessing the perfomance of bamboo structural components [Disertasi]. Pittsburgh (GB): University of Pittsburgh.
Nolan R. 2010. Determining Allowable Design Values for Wood. New York (US): American Forest and Paper Association and American Wood Council.
[ASTM] American Society for Testing and Material. 2005. Annual Book of ASTM Standard. Volume 0410. Wood. D-143-94 (Reapproved 2000): Standard Test Methods for Small Clear Specimens of Timber. West Conshohocken(US): ASTM International.
[ASTM] American Society for Testing and Material. 2002. Annual Book of ASTM Standard. Wood. D-245-00 (Reapproved 2002): Standard Practice for Establishing Structural Grades and Related Allowable Properties for Visually Graded Lumber. West Conshohocken(US): ASTM International.
[ASTM] American Society for Testing and Material. 2005. Annual Book of ASTM Standard volume 0410. Wood D-198-05 (Reapproved 2000): Standard Test Methods for Small Clear Specimens of Timber. West Conshohocken(US): ASTM International.
Brown HP, Panshin AJ, Forsaith CC. 1952. Textbook of Wood Technology. New York (US): McGraw Hill.
Glass SV, Zelinka SL. 2010. Moisture Relations and Physical Properties of Wood. Di dalam: [FPL] Forest Product Laboratory. Wood Handbook – Wood as an Engineering Material. Madison (US): Departement of Agriculture.
Kasmujo. 2001. Identifikasi Kayu dan Sifat-sifat Kayu. Jakarta(ID): Kanisius.
Bowyer JL, Haygreen JG, Shmulsky R. 2003. Forest Products and Wood Science:An Introduction. Iowa (US): IOWA State Press Blackwell Publishing.
Damanik RIM. Kekuatan Kayu. Medan(ID): USU. 2005.
Basri, E. dan Y.I. Mandang. Pengeringan kayu: Pentingnya pemahaman sifat-sifat kayu untuk mendukung teknologi pengolahan. [Prosiding]: Diskusi Teknologi Pemanfaatan Kayu Budidaya untuk Mendukung Industri Perkayuan yang Berkelanjutan. 7 November 2001: 261-268. Bogor (ID): Pusat Litbang Teknologi Hasil Hutan. 2001.
Marsoem SN, Prasetyo VE, Sulistyo J, Sudaryono, Lukmandaru G. Studi mutu kayu jati di hutan rakyat gunung kidul III. Sifat fisika kayu. Jurnal Ilmu Kehutanan. 2014; 8(2): 75-88.
Ruhendi S, Koroh DN, Syamani FA, Yanti H, Nurhaida, Saad S, Sucipto T. Analisis Perekatan Kayu. Bogor (ID): IPB Press. 2007.
Alokabel K, Lay YE, Wonlele T. Penentuan kelas kuat lokal di pulau Timor sebagai bahan konstruksi. JUTEKS. 2(2): 139-148. doi: 10.32511/juteks.v2i2.168.
Bahtiar ET. Keandalan modulus of elasticity (MOE) untuk menduga kekuatan kayu bercacat akibat lubang bor. JTHH. 2005; 18(2): 80-90.
Nowak T, Patalas F, Karolak A. Estimating mechanical properties of wood in existing structures-selected aspects. Materials. 2021; 14: 1-26. doi: 10.3390/ma14081941.
Ridley-Ellis D, Stapel P, Baño V. Strength grading of sawn timber in Europe: An explanation for engineers and researchers. European Journal of Wood and Wood Products. 2016; 74: 291-306. doi: 10.1007/s00107-016-1034-1.
Bodig J, Jayne BA. Mechanics of Wood and Wood Composite. Florida (US): Van Nostrand Reinhold Company. 1982.
Chauf KA, Dewi SM. Structural efficiency and flexural strength of mix-glulam timber beams are composed of sengon and coconut wood as green material construction. [Proceeding]: International Multidisiciplinary Conference 2016. November 15th, 2016: 362-370. Malang (ID): Brawijaya University. 2016.
Ross RJ. Wood Handbook: Wood as an EngineeringMaterial. Madisan (USA): Departement of Agriculture Forest Products Laboratory. 2010.
Awaludin A. Dasar-dasar Perencanaan Sambungan Kayu. Yogyakarta (ID) : Universitas Gadjah Mada. 2005.
Glos P. Strength Grading. Amsterdam (NL): Centrum Heut. 1994.
Kistiani F. Tinjauan kuat tekan dan kuat tarik kayu berdasarkan PKKI 1961, SNI M. 27-1991-03 dan SNI M. 25-1991-03. Media Komunikasi Teknik Sipil. 2006; 14(2): 206-213.
Rocha MFV, Costa LR, Costa LJ, Caxito AC, Soares BCD, Hein PRG. Wood knots influence the modulus of elasticity and resistance to compression. Floresta e Ambiente. 2018; 25(4): 1-6. doi: 10.1590/2179-8087.090617.
Ravenshorst GJP. Species independent strength grading of structural timber. [Disertation]. Delft (NL): Technische Universiteit Delft. 2015.
Mardikanto TR, Karlinasari L, Bahtiar ET. Sifat Mekanis Kayu. Bogor (ID): IPB Press. 2011.
Otaya LG. Distribusi probabilitas weibull dan aplikasinya. Jurnal Manajemen Pendidikan Islam. 2016; 4(2): 44-66.
Firmanti A, Bahtiar ET, Surjokusumo S, Komatsu K, Kawai S. Mechanical stress grading of tropical timbers without regard to species. J wood Sci. 2005; 51(1): 339-347. doi: 10.1007/s10086-004-0661-z.
Johannes AJH, Ekevad M, Girhammar UA, Berg S. Structural robustness of timber buildings- a review. Wood Material Science and Engineering. 2018; 14(2): 107-128. doi: 10.1080/17480272.2018.1446052.
Jorissen A, Fragiacomo M. General notes on ductility in timber structures. Eng Struct. 2011; 33(1):2987-2997. doi: 10.1016/j.engstruct.2011.07.024.
Tomasi R, Parisi MA, Piazzza M. Ductile design of glued-laminated timber beams. Practice Periodical on Structural Design and Construction. 2009; 14(3): 113-122. doi: 10.1080/17480272.2018.1446052.
Sulistiyawati I, Nugroho N, Surjokusumo S, Hadi YS. The bending strength of vertical and horizontal glued laminated lumber by transform cross section method. J. Trop Wood Sci. Technol. 2008; 6(2): 49-55.
Iswanto AH. Pengujian Modulus Elastisitas Kayu dengan Menggunakan Two Point Loading. Medan (ID): USU. 2008.
Gelder HA, Poorter L, Sterck FJ. Wood mechanics, allometry, and lifehistory variation in a tropical rain forest tree comunity. New Phytol. 2006; 171(1):367-378. doi: 10.1111/j.1469-8137.2006.01757.x.
Nie Y, Wei Y, Huang L, Liu Y, Dong F. Influence of slenderness ratio and sectional geometry on the axial compression behavior of original bamboo columns. J Wood Sci. 2021; 67(36):1-20. doi: 10.1186/s10086-021-01968-6.
Patel V, Liang QQ, Hadi MNS. Numerical analysis of high-strength concrete-filled steel tubular slender beam-columns under cyclic loading. Jounal of Constructional Steel Research. 2014; 92: 183-194. doi: 10.1016/j.jcsr.2013.09.008.
Hidayatullah H. Stabilitas balok kayu yang menerim pembebanan lentur terpusat di beberapa titik. [Tesis]. Bogor (ID): IPB. 2021.
Copyright (c) 2022 Jurnal Teknik Sipil dan Lingkungan
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Authors who publish with Jurnal Teknik Sipil dan Lingkungan, JSIL agree to the following terms:
a. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
b. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
c. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
