Ciri Finir Kupas Kayu Jabon (Anthocephalus cadamba)
Fast growing jabon is largely rotary-cut to produce veneer for plywood, com-ply, and LVL. In order to provide better information on veneer production and utilization, in this study the effects of wood juvenility and veneer thickness on lathe checks of jabon rotary-cut veneer were evaluated. Before veneer manufacturing, the jabon log was boiled at 50 and 75 °C for 4 and 8 hours respectively. The boiled logs were peeled to produce veneer of 1 and 2 mm thick. Lathe checks of veneers were measured under an optical video microscope. The rotary-cut veneer was grouped and evaluated separately at every segmented ring of 1 cm from pith to bark. The results showed that wood juvenility and veneer thickness had an important effect on lathe checks for the rotary-cut veneer. In general, the number of lathe check of the veneer increases with increasing veneer thickness and increase from pith to bark. Boiling of logs before rotary-cutting could decrease the value of lathe check. The results indicated that boiling of logs at 50 °C for 8 hours, and at 75 °C for 4 and 8 hours could minimize the number of lathe checks in manufacturing of 1 and 2 mm rotary-cut veneer from juvenile wood jabon.
Acevedo A, Bustos C, Lasserre, Gacitua, William JP. 2012. Nose bar pressure effect in the lathe check morphology to Eucalyptus nitens veneers. Maderas Cienc Tecnol. [online]. 1(3): 289-301. Epub 23-Ago-2012. ISSN 0718-221X. http://dx.doi.org/10.4067/S0718-221X2012005000004.
Bowyer JL, Shmulsky R, Haygreen JG. 2003. Forest Products and Wood Science: An Introduction. Ed. Ke-4. Iowa (US): A Blackwell Publ.
Bakar ES. 1995. Veneer Cutting With a Floating Bar. [Disertasi]. Laboratory of wood science and technology, Dept of Forestry, Tokyo (JP): Tokyo University of Agriculture.
Bakar ES. 1996. Faktor penentu mutu finir. J Teknol Has Hut. 9(2): 14–22.
Baldwin RF. 1995. Plywood and Veneer–Based Products: Manufacturing Practices. San Fransisco (US): Miller Freeman Inc.
Cumming JD, Fischer C, Dickinson FE. 1969. Rotary veneer cutting characteristics of young-growth redwood. For Prod J. 19(11): 26-30.
Cumming JD, Collett BM. 1970. Determining lathe settings for optimum veneer quality. For Prod J. 20(11): 20-27.
Darmawan W, Nandika D, Rahayu I, Fournier M, Marchal R. 2013. Determination of juvenile and mature transition ring for fast growing sengon and jabon wood. J Indian Acad Wood. 10: 39-47. Sci, DOI 10.1007/s13196-013-0091-x.
Daoui A, Descamps C, Marchal R, Zerizer A. 2011. Influence of veneer quality on beech LVL mechanical properties. Maderas Cien y Tecnol. 13(1): 69-83.
Dundar T, As N, Korkut S, Unsal O. 2008. The effect of boiling time on the surface roughness of rotary-cut veneers from oriental beech (Fagus orientalis L.). J Mater Proces Technol. 199: 119-123.
Dupleix A, Denaud L, Bleron L, Marchal R, Hughes M. 2012. The effect of log heating temperature on the peeling process and veneer quality: beech, birch, and spruce case studies. Europ J Wood Wood Prod. 71(2): 163-171.
Krisnawati H, Varis E, Kallio M, Kanninen M. 2011. Paraserianthes falcataria (L.) Nielsen: Ecology, Silviculture and Productivity. CIFOR, Bogor. 23 hlm.
Lutz JF. 1977. Wood Veneer : Log Selection, Cutting, and Drying. USDA Tech. Bull. No. 1577. 137 hlm.
Nazerian M, Ghalehno MD, Kashkooli AB. 2011. Effect of wood species, amount of juvenile wood and heat treatment on mechanical and physical properties of laminated veneer lumber. J Appl Sci. 11(6): 980-987.
Palka LC, Holmes B. 1973. Effect of Log Diameter and Clearance Angle on the Peel Quality of 0.125-inch-thick Douglas-Fir Veneer. Forest Prod. J. 23(7): 33-41.
Palka LC. 1974. Veneer cutting review - Factors Affecting and Models Describing the Process. Canadian Forestry Service, Western Forest Products Laboratory, Information Report VP-X- 135. 54 hlm.
Palubicki B, Marchal R, Butaud JC, Denaud LE, Bléron L, Collet R, Kowaluk G. 2009. A method of lathe check measurement; SMOF device and its software. Eur J Wood Prod. 68: 151-159.
Panshin AJ, De Zeeuw C. 1980. Textbook of Wood Technology: Structure, Identification, Properties and Uses of the Commercial Woods of the United States and Canada, Ed. Ke-4. New York (US): McGraw-Hill.
Suh JS, Kim SK. 1988. Effects of Softwood Log Pretreatments on The Veneer Peeling: Drying Properties and Plywood Properties. The Research Reports of the Forestry Research Institute. 37: 63-71.
Tsoumis G. 1991. Science and Technology of Wood: Structure, Properties and Utilization. New York (US): Van Nostrand Reinhold.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).